How to remove the rear valance for dual exhaust - Pontiac G6 Forum
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 25 (permalink) Old 11-22-2009, 03:53 PM Thread Starter
Michigan G6er
 
lcplmouw's Avatar
 
Join Date: Jun 2009
Location: Michigan
Posts: 217
 
How to remove the rear valance for dual exhaust

First order your new valance from gm.

Tools needed:
small screwdriver
7mm socket and ratchet or wrench

First remove the four screws on each side of the valance.



Second use a small screwdriver to remove the 4 clips on bottom of the valance


Third use a small screwdriver to carefully insert just below the bumper and the top of the valance and "pop" the clips off the top of the valance. Then the valance is removed.
Half way done.


Fourth remove the small clips off the old valance and place them on the new valance. The three small holes need clips not the big hole.


Dont forget the one on side.

Fifth Insert the clips on top of the valance into the bumper and hit it with your hand to make sure the clips are in all the way. Then insert the 4 screws on each side and the bottom clips.



Now your done. just need to get the dual exhaust installed.

Pontac G6 Sedan 3.5L
Exterior- 8000k HIDS lows, 8000k HIDs fog lights, 20% window tint, Tinted taillights, painted grilles (top and bottom) to match, Custom painted engine cover and battery box, Red painted calipers.
Performance- Crab Intake, Racing Line Performance strut tower brace, GT-R Custom Magnaflow exhaust.
Interior- red LED's on inside, custom painted interior trim to match outside, Memphis sub and Amp, Custom fiberglass sub enclosure.
lcplmouw is offline  
Sponsored Links
Advertisement
 
post #2 of 25 (permalink) Old 11-22-2009, 05:12 PM
Decepticon Extraordinaire
 
Lampoon's Avatar
 
Join Date: Sep 2005
Location: The Alamo
Posts: 5,348
    
Yeah....its really not hard at all. I wish mine didnt move so much going down the road.
I may have to shore it up somehow....

MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....

My Progession
Lampoon is offline  
post #3 of 25 (permalink) Old 11-22-2009, 05:17 PM Thread Starter
Michigan G6er
 
lcplmouw's Avatar
 
Join Date: Jun 2009
Location: Michigan
Posts: 217
 
how come it moves so much? the clips on the bottom hold it to the bumper reinforcement.

Pontac G6 Sedan 3.5L
Exterior- 8000k HIDS lows, 8000k HIDs fog lights, 20% window tint, Tinted taillights, painted grilles (top and bottom) to match, Custom painted engine cover and battery box, Red painted calipers.
Performance- Crab Intake, Racing Line Performance strut tower brace, GT-R Custom Magnaflow exhaust.
Interior- red LED's on inside, custom painted interior trim to match outside, Memphis sub and Amp, Custom fiberglass sub enclosure.
lcplmouw is offline  
Sponsored Links
Advertisement
 
post #4 of 25 (permalink) Old 11-22-2009, 05:20 PM
Decepticon Extraordinaire
 
Lampoon's Avatar
 
Join Date: Sep 2005
Location: The Alamo
Posts: 5,348
    
You will have to cut one of those out -thats in the way of your second (new) exhaust exit.
DId u notice that??

MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....

My Progession
Lampoon is offline  
post #5 of 25 (permalink) Old 11-22-2009, 07:00 PM
Lifetime Member
 
geewhiz's Avatar
 
Join Date: May 2008
Posts: 3,269
 
Quote:
Originally Posted by lcplmouw View Post
.
Super job, thanks




Mike
MODS;
None, if I want a faster car I'll buy one.
geewhiz is offline  
post #6 of 25 (permalink) Old 11-23-2009, 03:05 PM Thread Starter
Michigan G6er
 
lcplmouw's Avatar
 
Join Date: Jun 2009
Location: Michigan
Posts: 217
 
lampoon- no i didnt notice all mine went in and the exhaust hole is already in there. its all fine ( i think) all the clips on the bottom went in.

Pontac G6 Sedan 3.5L
Exterior- 8000k HIDS lows, 8000k HIDs fog lights, 20% window tint, Tinted taillights, painted grilles (top and bottom) to match, Custom painted engine cover and battery box, Red painted calipers.
Performance- Crab Intake, Racing Line Performance strut tower brace, GT-R Custom Magnaflow exhaust.
Interior- red LED's on inside, custom painted interior trim to match outside, Memphis sub and Amp, Custom fiberglass sub enclosure.
lcplmouw is offline  
post #7 of 25 (permalink) Old 02-22-2010, 05:59 AM
Member
 
stevenson_gt's Avatar
 
Join Date: Feb 2010
Posts: 48
 
rear valance for dual exhaust

were do i buy the rear valance for dual exhaust anyone know any sites or part number that i can give the dealer
stevenson_gt is offline  
post #8 of 25 (permalink) Old 02-22-2010, 06:43 AM
Decepticon Extraordinaire
 
Lampoon's Avatar
 
Join Date: Sep 2005
Location: The Alamo
Posts: 5,348
    
Did you try a search? I think I post it once a month or so.

Your GM parts counter or gmpartsdirect.com
I picked mine up from the dealership for around $80 or so....cant remember.

The GTP rear dual out back valance part # is: 22712778

MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....

My Progession
Lampoon is offline  
post #9 of 25 (permalink) Old 02-22-2010, 05:45 PM Thread Starter
Michigan G6er
 
lcplmouw's Avatar
 
Join Date: Jun 2009
Location: Michigan
Posts: 217
 
yes Lampoon is right. I just called my dealership and told them what i was looking for and they ordered it. It was like 115 total.

Pontac G6 Sedan 3.5L
Exterior- 8000k HIDS lows, 8000k HIDs fog lights, 20% window tint, Tinted taillights, painted grilles (top and bottom) to match, Custom painted engine cover and battery box, Red painted calipers.
Performance- Crab Intake, Racing Line Performance strut tower brace, GT-R Custom Magnaflow exhaust.
Interior- red LED's on inside, custom painted interior trim to match outside, Memphis sub and Amp, Custom fiberglass sub enclosure.
lcplmouw is offline  
post #10 of 25 (permalink) Old 02-23-2010, 04:59 AM
Member
 
stevenson_gt's Avatar
 
Join Date: Feb 2010
Posts: 48
 
and it fits perfect even tho its gtp
stevenson_gt is offline  
post #11 of 25 (permalink) Old 02-23-2010, 05:04 AM
Member
 
stevenson_gt's Avatar
 
Join Date: Feb 2010
Posts: 48
 
what one do i ask for ????http://www.buygmpartsworldwide.com/p...&siteid=215130


sorryfor all the little qustions im trying to do something with my 6 from everyone else in my area i hate being to same as everyone else
stevenson_gt is offline  
post #12 of 25 (permalink) Old 02-23-2010, 07:15 AM
Decepticon Extraordinaire
 
Lampoon's Avatar
 
Join Date: Sep 2005
Location: The Alamo
Posts: 5,348
    
your link doesnt work and Im not familiar with that business.

If you wish to use them you may want to call them with the part number.
Its a GM part.....soooooooo try your dealership parts counter or I gave you
another site where you would just drop in the number and buy it in my last post
(www.gmpartsdirect.com).

I just tried it:

Quote:
GM PART # 22712778
CATEGORY: License Plate Bracket/Plate
PACK QTY: 1
CORE CHARGE: $0.00
GM LIST: $116.10
OUR PRICE: $71.24

MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....

My Progession
Lampoon is offline  
post #13 of 25 (permalink) Old 02-23-2010, 07:18 AM
Decepticon Extraordinaire
 
Lampoon's Avatar
 
Join Date: Sep 2005
Location: The Alamo
Posts: 5,348
    
Quote:
Originally Posted by stevenson_gt View Post
and it fits perfect even tho its gtp
I have it on my 2005 and they didnt make a GTP in 2005.
Pix of my car are around the site somewhere... lol

It actually fits most of the G6's....unless you have an 09.5 model or
the GXP back fascia.

BTW- this is a How To Thread.

MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....

My Progession
Lampoon is offline  
post #14 of 25 (permalink) Old 02-25-2010, 07:13 AM
Member
 
stevenson_gt's Avatar
 
Join Date: Feb 2010
Posts: 48
 
The part number you gave me says its a licenes place frame or something are you shure thats it befor i buys it lol
stevenson_gt is offline  
post #15 of 25 (permalink) Old 02-25-2010, 08:22 AM
Decepticon Extraordinaire
 
Lampoon's Avatar
 
Join Date: Sep 2005
Location: The Alamo
Posts: 5,348
    
Please call your Pontiac Dealership and ask for the Parts Counter.
Verify all numbers before ordering cause Im not responsible for what you order. lol

MODS:
Crab Intakes CAB, MPD Ram Air hood, Custom exhaust,
WAMS High Performance Tune and a whole lot more....

My Progession
Lampoon is offline  
Sponsored Links
Advertisement
 
Reply

  Pontiac G6 Forum > Technical Discussion & Modifications > HOW-TO

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Pontiac G6 Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Similar Threads
Thread Thread Starter Forum Replies Last Post
How do you remove the rear bumper '05 sedan g6 Coldair Problems and Solutions 3 10-19-2009 05:14 PM
GXP front bumper and dual rear valance philip Appearance Modifications and Lighting 2 04-05-2009 06:54 PM
Remove rear speakers? ryguy76 Car Audio, Video and Security 6 01-31-2007 02:36 PM
Rear Lower Valance the_great_m Items Wanted 2 11-05-2006 01:25 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome